The control board is the main control for just about all of your GENERAL ELECTRIC washer? s capabilities. The switches, calls, and knobs all connect to the particular control board. In case it shorts away or gets broken, your machine will start to drop functionality or will stop working completely. Models having an electronic readout may also screen an error computer code telling you when the control table has stopped operating. If you such as fixing your very own appliances, this can be a repair you can help make yourself. Order replacement unit part #WH12X10468 for most GE washer models. Then stick to these steps to uninstall and exchange the old control board.
Unplug typically the washing machine.
This can be the first step in order to any appliance maintenance project. After you have discovered what? s incorrect with your washing machine, make sure a person unplug it entirely so you remain safe from electrical release and shock.
Disassemble the washer.
Move the washer away from the wall. You just need enough place to slide typically the top access panel back. If you have room, try to pull the washer away coming from the wall because little as achievable which means you don? t have to detach the hoses or switch off this particular.
Get rid of the three anchoring screws along the back edge of typically the top access section and the a few screws along the particular back of the lean next to the handle panel. Then you can certainly move the top panel an inch again, which loosens typically the hold on the front trim piece. Carefully pry the particular trim free of the particular tabs and place this aside. Lift the particular top panel? s i9000 back edge upward and then set the entire panel away.
Eliminate the control -panel next. To start out, move out the detergent drawer in the particular left-hand side plus depress the show behind the drawer to help you remove it entirely. Set it aside. Take away the twist next to the particular detergent drawer enclosure. Next, remove the screws along typically the back of the control panel system. Also, pry up the top border of the console to loosen the particular control panel. Carry onto the handle panel and hit the two securing tabs on the back again of the gaming system inside the cleaner. Once it comes free, don? https://ulsterappliancerepair.com pull it apart or let it tumble. Instead, tilt that down so you can commence to unplug the wires.
You can need to remove all of the wire harnesses connected to the management panel. All you have to do is press along the tab on each of your plug. You put on? t have to be able to worry about combining them up during reinstallation because every single plug has a good unique shape. Nevertheless, if you? re anxious about working with wiring, require an image from multiple perspectives so you have a visual guide of exactly where each wire harness should go.
As soon as the control panel is entirely detached from your cleaner, move it to a work area. This is typically the part that homes the control panel.
Remove the old control board.
Keep the control section face down. Get rid of the screws alongside the perimeter with the control board. There ought to be four. Also, depress the locking navigation bars along the border in the control board closest to the curving edge of typically the control panel. These can be difficult to reach, so employ a flathead electric screwdriver to move typically the tabs. Pull typically the control board out and shift the control panel apart.
Flip the management board over. Acquire a picture associated with all the buttons from the front part with the control board so that you have some sort of visual guide in the course of reinstallation. Then start off removing all of the keys and assemblies so you can maneuver them over to be able to the new element. They should be relatively loose, thus don? t utilize too much force on the slender plastic parts.
Install the new control board.
Prior to deciding to put the new control panel part in the handle panel console, set up all of the buttons you taken out from the older part. The more time assemblies will usually have hooks that really must be slid into the cutouts on typically the control board in order to provide extra stability. Make sure every of the switches is installed so they match the image guide.
Once the particular buttons are typical inside place, pick way up the control table and tilt it so that it? s almost perpendicular to the ground. Line up typically the control board? s shaft using the gap in the the control panel. As you carry out so, wiggle typically the knob a bit thus the shaft lines up with the gap and snaps completely into place. The control panel helps hold the buttons in place, but when you tilt typically the control board also far forward in this step, some involving the buttons may well come loose. when anything falls out of place, just reinsert the hooks and try out again.
Once typically the control board canal is within place, cautiously keep both items held together in addition to set the control panel face lower. Now you may lock the two bits together by gently pressing three locking tabs into location and retightening the particular four screws around the edge in the control board.
Reassemble the washer.
Very first, orient the handle board assembly beside the top associated with the front regarding the washer so the curved edge is closest to typically the machine. Start insert the wire wires into the handle board by using the picture guide or even by matching every single wire harness in order to the correct stopper.
Next, tilt typically the control panel support so it? h flush with typically the top front regarding the washer, and make sure none of the wires get pinched. Slide the tabs along the underside into the slots for the right part, and snap the particular control panel into place. There after, retighten the screw that sits down alongside the cleaning agent drawer housing. Likewise, retighten the anchoring screws along the back of the control panel. Next slide the detergent drawer into place and reattach typically the top access section. If you look at the underside from the top access panel, you? ll notice slots regarding the circular hooks along the railroad. The pins require through the greater end of typically the cutout hence the -panel lies flat in addition to then, when you slide the -panel forward, lock straight into place against the particular smaller area of the particular cutout. This part can be tricky, so a visible guide like from the end of this video might help.
To get this done, set the top access panel carefully together with the frame along with the pins. It need to hand approximately a great inch off the back. Before a person slide the panel forward, press the trim into place on three locking tabs. Then glide the panel ahead and add again all six screws to hold this set up.
Push the washer back into place and plug it in. Follow the guide that came with typically the control board to program the washing machine. Each model provides a different step. When your washer has been programmed, it? s prepared to start off a new cycle.